Skip to Content

How To Fix Hisense TV Not Turning On (Explained)

How To Fix Hisense TV Not Turning On (Explained)

It’s a Saturday night, and your favorite show is airing. You ordered pizza and are all cozy on your sofa waiting. You turn your Hisense TV on, but it doesn’t respond. You start to panic as your relaxation and excitement turn into sorrow and despair.

Worry not because, in this article, I’ll be discussing all the possible fixes for a Hisense TV not turning on. So if you are facing this issue, then read on.

What to do?Why do it?
Reconnect the TV to the wall outlet.Check if your TV is properly connected to the wall socket. Maybe your connection is loose, and the cable is not perfectly plugged in.
Check if your TV is turned onThe wall plug might be defective, and your TV isn’t getting power supply.
Change your power cordA damaged power cable may not receive sufficient electricity.
Try disconnecting your devicesSometimes connected devices like a set-top box or streaming devices may not be functioning correctly.
Check whether the backlight is onDue to faulty backlights, your TV will not display images.
Check your router’s settingsTry resetting your router or unplug it to see if this resolves the issue.
Do a hard resetIf nothing works, try hard resetting your TV. It will clean up all the mess and hopefully, now your TV will turn on.
Hisense TV won’t turn on fixes

Why is my Hisense TV not turning on?

There can be several reasons why your Hisense TV isn’t turning on, such as:

The power cord is not plugged in.

If the power cord isn’t plugged in, then the TV won’t receive any power and so won’t turn on.

A fuse has blown.

If a fuse in your wiring or TV has blown, then it could stop the flow of electricity.

There is a power outage.

A power outage will also have similar effects on the TV. It won’t receive any electricity so it won’t turn on.

The remote control batteries are flat.

If you’re using a remote to turn the TV on and the batteries inside the remote have died, then the signals won’t reach the TV.

Problems with hardware and software.

Some hardware and software issues can disrupt the current flow. They can also disrupt the transmission of electrical signals.

Hisense TV
Hisense TV

1. Reset the TV

If your Hisense TV won’t turn on, make sure the power cord is properly seated in the back of the TV, and then try a different wall outlet. If the TV still doesn’t turn on, unplug it from the wall, wait 60 seconds, and then reconnect it.

2. Check if your TV is turned on.

Perhaps your Hisense TV is fine, but the wall plug is faulty. The TV will receive little to no power and thus will not turn on.

It may occasionally start and stop without warning. It may also do this repeatedly due to a faulty outlet connection.

To check if the main problem lies in your wall outlet, follow these guidelines:

  1. Disconnect your television from the wall outlet.
  2. Check that all other devices are working, particularly those that require a higher power supply.
  3. Try to plug your TV into other power outlets.
  4. Remove all power surge suppressors and extensions and plug a device that you know works properly into the wall.
  5. Try to connect your Hisense TV again to the wall.
  6. Switch on the button that can be found beneath the TV and check whether the power light has lit up or not.

3. Make sure your power cable is working properly.

When the power cord on the TV is faulty, it may receive insufficient or no power supply. Depending on the amount of current it receives, the red power light may illuminate or fail.

To see if the power cord is faulty, do the following:

  1. Examine the cable to see if any wires are cut, uninsulated, or short-circuited.
  2. Check if your Hisense TV will work by borrowing a power cord from a friend or a repairman.
  3. Check to see if the red power light comes on at all.
  4. If this step fails, the issue may be with the TV firmware or motherboard.

4. Check the input source.

When there’s no input source, some Hisense TV models enter standby mode. If you use a streaming device or a set-top box, your TV may automatically go into standby mode if the device or its connecting wires fail. The TV sound may work properly at times, but there’s no picture.

Here’s how to deal with it:

  1. Switch the TV on and off to see if it briefly lights up before going dark.
  2. Check the TV input ports to see if others work.
  3. Connect other devices, such as your decoder, streaming box, or phone, using the same cable.
  4. Alter the cables you’re using, such as VGA, HDMI, or RCA.
A girl standing beside a TV
A girl standing beside a TV

5. Examine your TV settings.

Some changes made by children on television without their knowledge cause them to behave strangely. For example, if your television blinks several times but doesn’t turn on, it may be experiencing configuration issues. As a result, you must delete all configuration files and reset the device to factory settings. Do the following:

  1. Remove all connected devices as well as the power cable from your television.
  2. Locate the power button on your television. The button may be located at the back or bottom of your TV, depending on the model.
  3. Holding down the power button for 30 seconds will drain all power from the TV.
  4. Wait about 20 to 30 minutes before turning on your television again.
  5. Turn on your television to see if the problem has been resolved.

6. Check for hardware issues.

The failure of LED backlights is the most common hardware issue in Hisense TVs. Although your TV doesn’t display images, the sound and red power lights function properly. A short in the mainboard or power board circuitry can cause LED backlights to fail.

Here’s what you should do:

  1. Turn on a flashlight and aim it at the television.
  2. Check to see if there are any visible images or words on display. Your backlight circuit is probably broken if you can see letters or images.
  3. To be sure, repeat the above procedure to reset the brightness settings to default and see if this works for you.
  4. If the LED backlights are broken, you can have them replaced by a repairman.

7. Ensure your internet connection is all set.

The power light on your Hisense Smart TV may flash red or blue 2 to 6 times, but the display doesn’t turn on.

This issue could be caused by a bad connection with your modem or router, a power deflection issue, or a motherboard issue with your TV.

8. Make sure your TV is getting the appropriate power supply.

Check to see if the power light located on the front of the TV is lighting. It indicates that the TV is getting enough power. If the power light is illuminated, then most probably there’s a problem with your remote.

Remember to remove any object that could hinder signal transmission between the remote and the TV’s receiver. Also, remove electronic devices from the vicinity of the television, at least temporarily, to eliminate the possibility of external interference.

If the problem persists, it’s time to troubleshoot the remote.

Hisense TV display center
Hisense TV display center

9. Restore it back to default settings.

If you haven’t fixed the problem yet, or if it keeps recurring, perform a factory reset. It will remove all installed applications as well as the default settings. Follow the steps below to hard reset your television:

  1. Go to the small hole labeled “TV RESET.”
  2. Insert a paper clip into the hole after it has been bent.
  3. For about 15 seconds, press the clip into the hole.
  4. Hold the clip inside the hole until the TV turns back on.

10. Contact customer support

If all of the preceding steps have failed, you most likely have a faulty unit. As a result, you should contact customer service to find out if this is the case.

You should have the following information when approaching the support team:

  • The model number of your Hisense television.
  • The serial number of the remote.
  • The date you bought the remote.

Hisense will be able to check your warranty information and see if you qualify for a new, free remote with these details. Hisense customer service can be reached at 1888.935.8880. Their hours of operation are Monday through Friday, 9.00 a.m. to 9.00 p.m. EST. On weekends, call between 9 a.m. and 6 p.m. EST.

A video about how to fix a Hisense tv that won’t turn on

Conclusion

  • Your Hisense TV not turning on can be due to multiple reasons such as a power outage, faulty remotes, faulty power cords, a blown fuse, or other software and hardware issues.
  • You should try resetting and factory resetting your TV before trying anything else.
  • Next, you can try changing the power outlet or buying another power cord.
  • You can troubleshoot your remote to see if that’s where the problem lies.
  • You can also try unplugging all network devices and disconnecting other devices.
  • If all of these fixes fail, then as a last resort, you should contact customer support.

FAQs

Q: Is Hisense a good TV brand?

A: There’s no definitive answer to this question since opinions will vary. Some people may find Hisense to be a good TV brand, while others may have had problems with their Hisense TV and prefer another brand.

Q: Is Hisense owned by Samsung?

A: Hisense is not owned by Samsung, although the two companies have a partnership.

Q: Do Hisense TVs have problems?

A: There’s no clear-cut answer to this question since people may have different viewpoints regarding its performance. Some people may have had problems with their Hisense TV, while others may find the brand to be reliable.

Q: Is Hisense a better TV than Samsung?

A: This is a difficult question to answer since both brands have their own strengths and weaknesses. Some people may prefer Hisense TVs, while others may prefer Samsung TVs.

Other Articles