How To Clean Your Dyson V8 (A Step-by-Step Guide)

Maintaining your Dyson V8 in pristine condition is crucial for ensuring it performs its best. If you’re among the many owners of a Dyson V8, you might be curious about the best ways to keep your vacuum functioning smoothly.

Caring for your Dyson V8 is straightforward. Make it a routine to empty the dust bin and clean both the pre-filter and post-filter using only cold water. It’s crucial to let the filters completely dry, ideally for 24 hours, before putting them back. Additionally, examine the brush roll for any trapped debris and gently clean the vacuum’s exterior with a dry cloth.

Don’t worry, we’ve got you covered! This guide will help you navigate through cleaning and maintaining your Dyson V8. We’ll cover everything from performing a thorough clean to tackling any typical problems that might arise.

These comprehensive steps will help you keep your beloved Dyson V8 running smoothly for years. So, let’s start by looking at what needs to be done to keep your machine in top condition!

Gather The Necessary Supplies: Filters, Brushes And Detergent

Having the right supplies to clean your Dyson V8 properly is important. To begin, you’ll need a filter, a rotating brush, and detergent specifically designed for a Dyson V8 vacuum cleaner.

The filter is essential to keeping the dust and dirt out of the machine. Check it regularly—based on how often you use your vacuum—for any signs of wear or damage. You can purchase replacement filters from the Dyson website if needed.

The rotating brush helps loosen dirt, and debris stuck deep within the carpet or upholstery; think of it as a mini scrubbing brush for your vacuum! It’s important to clean this after each use—simply remove it from the head and rinse it with water.

Finally, using a detergent specifically designed for a Dyson V8 is key to maintaining your machine’s performance; generic detergents may cause foaming and build-up over time, which can clog its internal parts and reduce suction power.

Remove And Empty The Dirt Compartment

Removing and emptying the dirt compartment is an essential part of maintaining your Dyson V8 vacuum. It’s important to do this step on a regular basis to make sure your vacuum runs optimally and picks up as much dirt as possible.

Here’s what you need to do:

• Turn off the power switch, and then unplug the cord.
• Squeeze the collar on either side of the cyclone and pull apart the cyclone assembly from the machine’s body.
• Remove the dust compartment from its clip at the back of the machine and empty it into a bin.
• Rinse any dirt sticking to the sides with warm water, dry it, then reattach it securely with its clip.
• Reassemble all parts before turning it back on and plugging it into your machine.

Wash The Filters: HEPA, Motorhead Tool And Extension Hose

It’s important to periodically clean the filters on your Dyson V8 vacuum to keep it running effectively and efficiently. Here are the steps you should follow for cleaning each type of filter:

HEPA Filter

1. Disconnect the machine and remove the filter from the dust bin.
2. Rinse it with cold water and leave it to dry naturally overnight.
3. Once dry, put it back in the machine and reconnect.

Fun Fact: The average lifespan of a Dyson V8 is 10 years.

Motorhead Tool

1. Unscrew the motorhead tool and remove the filter inside it.
2. Shake off any dust or dirt, then use a vacuum cleaner wand to brush away any remaining debris carefully.
3. Allow the filter to air-dry completely before putting it back into position in the motorhead tool and reattaching everything properly.

Extension Hose Filter

1. Detach your extension hose from both ends of your Dyson V8 vacuum cleaner.
2. Take off the small plastic filter by gently pulling upwards on both sides at once, then clean using a vacuum cleaner wand or compressed air jet set to a low-pressure setting, taking care not to damage any plastic parts during the cleaning process.
3. Allow the filter to fully dry before replacing the extension hose and reattaching everything correctly back together with your Dyson V8 vacuum cleaner system

Clean The Brushes and Tools: Fluffy Brush, Direct Drive Cleaner Head And Extension Wand

Cleaning the Brushes and Tools is an important step, ensuring that your Dyson V8 keeps cleaning effectively. First, remove the Fluffy Brush and Direct Drive Cleaner Head attachments from the Extension Wand.

Use a vacuum cleaner brush attachment or a dry cloth to remove any dust or debris from these parts gently. Next, soak them in warm, soapy water and scrub vigorously with a soft brush to loosen dirt particles. Rinse with clean water afterward and let all parts air dry completely before reassembling.

The Extension Wand can also be cleaned using a vacuum cleaner brush attachment or dry cloth, as well as some mild soap and warm water for heavier dirt particles. Ensure you rinse the wand properly before refitting any attachments.

Finally, reattach the Fluffy Brush, Direct Drive Cleaner Head, and extension wand back together before continuing cleaning with your Dyson V8.

Wipe Down The Exterior And Empty Cyclone

Now it’s time to get to the outside of your Dyson V8. You’ll want to start by wiping the exterior with a damp cloth. Be sure to pay careful attention to the cyclone since this is where much dirt and dust can accumulate over time.

You’ll want to empty the cyclone once you’ve wiped down the external surfaces. To do this, simply detach the cyclone from the main body of your Dyson V8 and empty its contents into a trash bag.

It’s best to do this over a garbage can in case any dirt or debris falls out when you’re emptying it. Once emptied, you can use your damp cloth to clean any remaining dirt or debris inside the cyclone chamber before reassembling it with your vacuum cleaner.

Reassemble Your Dyson V8 And Test It

Reassembling your Dyson V8 is the last step in cleaning it properly. Fortunately, it is a straightforward process. First, ensure all the parts have been cleaned and dried, then start putting them back together.

1. Begin by attaching the hose to the cyclone assembly and fixing it in place with the latch.
2. Next, attach both ends of the flexible hose and secure them with a clip.
3. Place the wand back into the cyclone assembly and fasten it with a latch.
4. Insert the floor head into the wand and secure it with a twist-and-lock motion.
5. Connect the power cable to both parts of your cleaner before plugging it into an electrical outlet to run a test cycle and ensure everything works correctly.

Once you’re done, you can enjoy peace of mind knowing that your Dyson V8 is clean and ready for use!

FAQs

How Often Should I Clean The Filter Assembly On My Dyson V8?

It is recommended to clean the filter assembly every month, or more often if you use the vacuum frequently or if you have pets.

Can I Use Soap Or Detergent To Wash The Filter Assembly?

No, you should not use soap or detergent to wash the filter assembly. Only use water and make sure to squeeze out any excess water before leaving it to dry.

What Should I Do If My Dyson V8 Is Still Not Picking Up Dirt Or Debris After Cleaning It?

If your Dyson V8 is still not working properly after cleaning it, there may be a blockage in the vacuum’s airways. Check for any blockages and clear them if necessary. If the issue persists, contact Dyson customer support for assistance.

Conclusion

• With this step-by-step Dyson V8 Cleaning Guide, you now have the knowledge and the tools needed to get your vacuum back in excellent condition.
• The key takeaway to remember is to always follow the manufacturer’s instruction, clean your vacuum regularly, and use the right tools and techniques.
• By doing so, you’ll ensure that your Dyson V8 remains in top shape, and will make vacuuming hassle-free and efficient. So what are you waiting for? Get cleaning today!

Other Articles

• Solved: Dyson Airwrap Blinking Red/White And How to Fix It (Find Out)
• Smart Pressure Washers (Explained)
• Dirt Dilemma Resolved: Fixing Roomba’s Inability to Pick Up